Обсуждение Tomatousb Shibby

[Pavel81]

я накатил 107 сегодня поверх 102, заметил, что стал постоянно падать transmission, пока поставил ему скрипт перезапуска каждые 15 минут, вот разберусь с локальной сетью и вернусь на 102.

[Radjah]

Народ что делать ? уходит в ребут довольно часто , в логах пишет постоянно одну и ту же ошибку
Apr 3 23:20:46 unknown daemon.err apcupsd[383]: apcupsd FATAL ERROR in linux-usb.c at line 609 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see <http://www.apcupsd.com/support.html>.
Apr 3 23:20:46 unknown daemon.err apcupsd[383]: apcupsd error shutdown completed

Роутер умеет с подключенным UPS работать, но его скорее всего нет, вот и жалуется.
А причин ребутов может быть вагон. От глюков ядра до банального перегрева.

[Pavel81]

Привёл я таблицу маршрутизации к такому виду на данный момент:

Код: Выделить всё

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
178.217.24.250  *               255.255.255.255 UH    0      0        0 ppp0
192.168.1.0     *               255.255.255.0   U     0      0        0 br0
192.168.0.0     lancore.p-t-k.l 255.255.0.0     UG    0      0        0 vlan2
172.20.0.0      *               255.252.0.0     U     0      0        0 vlan2
172.16.0.0      lancore.p-t-k.l 255.240.0.0     UG    0      0        0 vlan2
10.0.0.0        lancore.p-t-k.l 255.0.0.0       UG    0      0        0 vlan2
127.0.0.0       *               255.0.0.0       U     0      0        0 lo
default         sov33-bras2-lo1 0.0.0.0         UG    0      0        0 ppp0

Осталось только добыть строчку туда тогда станет как на заводской, где всё работало, но возможно ещё понадобятся какие-то правила:
default lancore.p-t-k.l 0.0.0.0 UG 1 0 0 eth0

[Deks]

Подскажите по настройкам Bandwidth Limiter для гостевой сети на br1

Что вписывать в Download rate и Download ceil?
Я так понимаю что ceil - это максимально возможная скорость, а rate - это когда несколько клиентов упираются в макс скорость и их откатывает на rate?

[Nite2]

Deks, rate - это гарантированная полоса. У вас могут быть другие клиенты, не подпадающие под это правило. Как только начинает работать клиент, подпадающий под правило, QoS подвигает других клиентов, чтобы дать этому (или этим) полосу, указанную в rate.
Если же канал не занят, QoS может выделить и бОльшую полосу, но не больше ceil.

[MatrixNet]

Привет, у меня следующая проблема помогите плз

 

Jan 1 03:00:51 unknown syslog.info syslogd started: BusyBox v1.20.2
Jan 1 03:00:51 unknown user.notice kernel: klogd started: BusyBox v1.20.2 (2013-03-04 09:16:41 CET)
Jan 1 03:00:51 unknown user.notice kernel: Linux version 2.6.22.19 (root@tomato) (gcc version 4.2.4) #4 Mon Mar 4 09:38:31 CET 2013
Jan 1 03:00:51 unknown user.warn kernel: CPU revision is: 00019749
Jan 1 03:00:51 unknown user.warn kernel: Determined physical RAM map:
Jan 1 03:00:51 unknown user.warn kernel: memory: 07fff000 @ 00000000 (usable)
Jan 1 03:00:51 unknown user.debug kernel: Entering add_active_range(0, 0, 32767) 0 entries of 256 used
Jan 1 03:00:51 unknown user.info kernel: Zone PFN ranges:
Jan 1 03:00:51 unknown user.warn kernel: Normal 0 -> 32767
Jan 1 03:00:51 unknown user.warn kernel: HighMem 32767 -> 32767
Jan 1 03:00:51 unknown user.info kernel: early_node_map[1] active PFN ranges
Jan 1 03:00:51 unknown user.warn kernel: 0: 0 -> 32767
Jan 1 03:00:51 unknown user.debug kernel: On node 0 totalpages: 32767
Jan 1 03:00:51 unknown user.debug kernel: Normal zone: 0 pages used for memmap
Jan 1 03:00:51 unknown user.debug kernel: Normal zone: 0 pages reserved
Jan 1 03:00:51 unknown user.debug kernel: Normal zone: 32767 pages, LIFO batch:7
Jan 1 03:00:51 unknown user.debug kernel: HighMem zone: 0 pages used for memmap
Jan 1 03:00:51 unknown user.warn kernel: Built 1 zonelists. Total pages: 32767
Jan 1 03:00:51 unknown user.notice kernel: Kernel command line: root=/dev/mtdblock15 console=ttyS0,115200
Jan 1 03:00:51 unknown user.warn kernel: Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
Jan 1 03:00:51 unknown user.warn kernel: Primary data cache 32kB, 4-way, linesize 32 bytes.
Jan 1 03:00:51 unknown user.info kernel: Synthesized TLB refill handler (20 instructions).
Jan 1 03:00:51 unknown user.info kernel: Synthesized TLB load handler fastpath (32 instructions).
Jan 1 03:00:51 unknown user.info kernel: Synthesized TLB store handler fastpath (32 instructions).
Jan 1 03:00:51 unknown user.info kernel: Synthesized TLB modify handler fastpath (31 instructions).
Jan 1 03:00:51 unknown user.warn kernel: PID hash table entries: 512 (order: 9, 2048 bytes)
Jan 1 03:00:51 unknown user.err syslog: module usbcore not found in modules.dep
Jan 1 03:00:52 unknown user.warn kernel: CPU: BCM5357 rev 2 pkg 10 at 480 MHz
Jan 1 03:00:52 unknown user.warn kernel: Using 240.000 MHz high precision timer.
Jan 1 03:00:52 unknown user.info kernel: console [ttyS0] enabled
Jan 1 03:00:52 unknown user.warn kernel: Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Jan 1 03:00:52 unknown user.warn kernel: Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Jan 1 03:00:52 unknown user.info kernel: Memory: 126464k/131068k available (33k kernel code, 4452k reserved, 2957k data, 128k init, 0k highmem)
Jan 1 03:00:52 unknown user.debug kernel: Calibrating delay loop... 239.20 BogoMIPS (lpj=1196032)
Jan 1 03:00:52 unknown user.warn kernel: Mount-cache hash table entries: 512
Jan 1 03:00:52 unknown user.info kernel: NET: Registered protocol family 16
Jan 1 03:00:52 unknown user.info kernel: usbcore: registered new interface driver usbfs
Jan 1 03:00:52 unknown user.info kernel: usbcore: registered new interface driver hub
Jan 1 03:00:52 unknown user.info kernel: usbcore: registered new device driver usb
Jan 1 03:00:52 unknown user.warn kernel: PCI: no core
Jan 1 03:00:52 unknown user.warn kernel: PCI: no core
Jan 1 03:00:52 unknown user.warn kernel: PCI: Fixing up bus 0
Jan 1 03:00:52 unknown user.info kernel: NET: Registered protocol family 2
Jan 1 03:00:52 unknown user.info kernel: Time: MIPS clocksource has been installed.
Jan 1 03:00:52 unknown user.warn kernel: IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
Jan 1 03:00:52 unknown user.warn kernel: TCP established hash table entries: 4096 (order: 3, 32768 bytes)
Jan 1 03:00:52 unknown user.warn kernel: TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
Jan 1 03:00:52 unknown user.info kernel: TCP: Hash tables configured (established 4096 bind 4096)
Jan 1 03:00:52 unknown user.info kernel: TCP reno registered
Jan 1 03:00:52 unknown user.info kernel: squashfs: version 3.0 (2006/03/15) Phillip Lougher
Jan 1 03:00:52 unknown user.info kernel: io scheduler noop registered (default)
Jan 1 03:00:52 unknown user.info kernel: HDLC line discipline: version $Revision: 4.8 $, maxframe=4096
Jan 1 03:00:52 unknown user.info kernel: N_HDLC line discipline registered.
Jan 1 03:00:52 unknown user.info kernel: Serial: 8250/16550 driver $Revision: 1.90 $ 2 ports, IRQ sharing disabled
Jan 1 03:00:52 unknown user.info kernel: serial8250: ttyS0 at MMIO 0xb8000300 (irq = 8) is a 16550A
Jan 1 03:00:52 unknown user.info kernel: PPP generic driver version 2.4.2
Jan 1 03:00:52 unknown user.info kernel: MPPE/MPPC encryption/compression module registered
Jan 1 03:00:52 unknown user.info kernel: NET: Registered protocol family 24
Jan 1 03:00:52 unknown user.info kernel: PPPoL2TP kernel driver, V0.18.3
Jan 1 03:00:52 unknown user.info kernel: PPTP driver version 0.8.5
Jan 1 03:00:52 unknown user.err kernel: pflash: found no supported devices
Jan 1 03:00:52 unknown user.warn kernel: Found an ST compatible serial flash with 0 64KB blocks; total size 0MB
Jan 1 03:00:52 unknown user.err kernel: sflash: found no supported devices
Jan 1 03:00:52 unknown user.warn kernel: Found a Samsung NAND flash with 2048B pages or 128KB blocks; total size 128MB
Jan 1 03:00:52 unknown user.notice kernel: nflash: squash filesystem with lzma found at block 6303
Jan 1 03:00:52 unknown user.warn kernel: Boot partition size = 524288(0x80000)
Jan 1 03:00:52 unknown user.notice kernel: Creating 16 MTD partitions on "nflash":
Jan 1 03:00:52 unknown user.notice kernel: 0x00000000-0x00080000 : "boot"
Jan 1 03:00:52 unknown user.notice kernel: 0x00080000-0x00200000 : "nvram"
Jan 1 03:00:52 unknown user.notice kernel: 0x00200000-0x00240000 : "board_data"
Jan 1 03:00:52 unknown user.notice kernel: 0x00240000-0x00280000 : "POT1"
Jan 1 03:00:52 unknown user.notice kernel: 0x00280000-0x002c0000 : "POT2"
Jan 1 03:00:52 unknown user.notice kernel: 0x002c0000-0x00300000 : "T_Meter1"
Jan 1 03:00:52 unknown user.notice kernel: 0x00300000-0x00340000 : "T_Meter2"
Jan 1 03:00:52 unknown user.notice kernel: 0x00340000-0x00380000 : "ML1"
Jan 1 03:00:52 unknown user.notice kernel: 0x00380000-0x003c0000 : "ML2"
Jan 1 03:00:52 unknown user.notice kernel: 0x003c0000-0x00400000 : "ML3"
Jan 1 03:00:52 unknown user.notice kernel: 0x00400000-0x00440000 : "ML4"
Jan 1 03:00:52 unknown user.notice kernel: 0x00440000-0x00480000 : "ML5"
Jan 1 03:00:52 unknown user.notice kernel: 0x00480000-0x004c0000 : "ML6"
Jan 1 03:00:52 unknown user.notice kernel: 0x004c0000-0x00500000 : "ML7"
Jan 1 03:00:52 unknown user.notice kernel: 0x00500000-0x02000000 : "linux"
Jan 1 03:00:52 unknown user.notice kernel: 0x00627f4c-0x02000000 : "rootfs"
Jan 1 03:00:52 unknown user.warn kernel: _nvram_init: allocat header: 2280849408, size= 32768
Jan 1 03:00:52 unknown user.info kernel: usbcore: registered new interface driver hiddev
Jan 1 03:00:52 unknown user.info kernel: usbcore: registered new interface driver usbhid
Jan 1 03:00:52 unknown user.info kernel: drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
Jan 1 03:00:52 unknown user.warn kernel: u32 classifier
Jan 1 03:00:52 unknown user.warn kernel: OLD policer on
Jan 1 03:00:52 unknown user.warn kernel: Netfilter messages via NETLINK v0.30.
Jan 1 03:00:52 unknown user.warn kernel: nf_conntrack version 0.5.0 (1024 buckets, 8192 max)
Jan 1 03:00:52 unknown user.warn kernel: ip_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 03:00:52 unknown user.info kernel: ipt_account 0.1.21 : Piotr Gasidlo <quaker@barbara.eu.org>, http://www.barbara.eu.org/~quaker/ipt_account/
Jan 1 03:00:52 unknown user.warn kernel: net/ipv4/netfilter/tomato_ct.c [Mar 4 2013 09:09:02]
Jan 1 03:00:52 unknown user.info kernel: NET: Registered protocol family 1
Jan 1 03:00:52 unknown user.info kernel: NET: Registered protocol family 10
Jan 1 03:00:52 unknown user.warn kernel: ip6_tables: (C) 2000-2006 Netfilter Core Team
Jan 1 03:00:52 unknown user.info kernel: NET: Registered protocol family 17
Jan 1 03:00:52 unknown user.info kernel: 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
Jan 1 03:00:52 unknown user.info kernel: All bugs added by David S. Miller <davem@redhat.com>
Jan 1 03:00:52 unknown user.warn kernel: VFS: Mounted root (squashfs filesystem) readonly.
Jan 1 03:00:52 unknown user.info kernel: Freeing unused kernel memory: 128k freed
Jan 1 03:00:52 unknown user.warn kernel: Warning: unable to open an initial console.
Jan 1 03:00:52 unknown user.warn kernel: emf: module license 'Proprietary' taints kernel.
Jan 1 03:00:52 unknown user.debug kernel: PCI: Setting latency timer of device 0000:00:02.0 to 64
Jan 1 03:00:52 unknown user.warn kernel: eth0: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 5.100.138.20
Jan 1 03:00:52 unknown user.warn kernel: wl_module_init: passivemode set to 0x0
Jan 1 03:00:53 unknown user.debug kernel: PCI: Setting latency timer of device 0000:00:01.0 to 64
Jan 1 03:00:53 unknown user.warn kernel: eth1: Broadcom BCM4329 802.11 Wireless Controller 5.100.138.20
Jan 1 03:00:53 unknown user.warn kernel: Algorithmics/MIPS FPU Emulator v1.5
Jan 1 03:00:53 unknown user.notice kernel: SCSI subsystem initialized
Jan 1 03:00:53 unknown user.info kernel: Initializing USB Mass Storage driver...
Jan 1 03:00:53 unknown user.info kernel: usbcore: registered new interface driver usb-storage
Jan 1 03:00:53 unknown user.info kernel: USB Mass Storage support registered.
Jan 1 03:00:53 unknown user.info kernel: ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
Jan 1 03:00:53 unknown user.debug kernel: PCI: Setting latency timer of device 0000:00:04.1 to 64
Jan 1 03:00:53 unknown user.info kernel: ehci_hcd 0000:00:04.1: EHCI Host Controller
Jan 1 03:00:53 unknown user.info kernel: ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 1
Jan 1 03:00:53 unknown user.info kernel: ehci_hcd 0000:00:04.1: irq 5, io mem 0x18004000
Jan 1 03:00:53 unknown user.info kernel: ehci_hcd 0000:00:04.1: USB 0.0 started, EHCI 1.00
Jan 1 03:00:53 unknown user.info kernel: usb usb1: configuration #1 chosen from 1 choice
Jan 1 03:00:53 unknown user.info kernel: hub 1-0:1.0: USB hub found
Jan 1 03:00:53 unknown user.info kernel: hub 1-0:1.0: 2 ports detected
Jan 1 03:00:53 unknown user.debug hotplug[473]: Attached USB device 1-0:1.0 [INTERFACE=9/0/0 PRODUCT=1d6b/2/206]
Jan 1 03:00:53 unknown user.info kernel: usbcore: registered new interface driver usblp
Jan 1 03:00:53 unknown user.info kernel: usblp: USB Printer Device Class driver
Jan 1 03:00:54 unknown user.info kernel: usb 1-1: new high speed USB device using ehci_hcd and address 2
Jan 1 03:00:54 unknown user.info kernel: usb 1-1: configuration #1 chosen from 1 choice
Jan 1 03:00:54 unknown user.info kernel: hub 1-1:1.0: USB hub found
Jan 1 03:00:54 unknown user.info kernel: hub 1-1:1.0: 7 ports detected
Jan 1 03:00:54 unknown user.debug hotplug[488]: Attached USB device 1-1:1.0 [INTERFACE=9/0/1 PRODUCT=1a40/201/100]
Jan 1 03:00:54 unknown user.info kernel: usb 1-1.2: new full speed USB device using ehci_hcd and address 3
Jan 1 03:00:54 unknown user.info kernel: usb 1-1.2: configuration #1 chosen from 1 choice
Jan 1 03:00:54 unknown user.debug hotplug[522]: Attached USB device 1-1.2:1.0 [INTERFACE=7/1/2 PRODUCT=4e8/3292/100]
Jan 1 03:00:55 unknown user.info kernel: usblp0: USB Bidirectional printer dev 3 if 0 alt 0 proto 2 vid 0x04E8 pid 0x3292
Jan 1 03:00:55 unknown user.info kernel: usb 1-1.6: new high speed USB device using ehci_hcd and address 4
Jan 1 03:00:55 unknown user.debug kernel: vlan1: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 03:00:55 unknown user.debug kernel: vlan1: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 03:00:55 unknown user.info kernel: vlan1: dev_set_allmulti(master, 1)
Jan 1 03:00:55 unknown user.info kernel: usb 1-1.6: configuration #1 chosen from 1 choice
Jan 1 03:00:55 unknown user.info kernel: scsi0 : SCSI emulation for USB Mass Storage devices
Jan 1 03:00:55 unknown user.debug hotplug[540]: Attached USB device 1-1.6:1.0 [INTERFACE=8/6/80 PRODUCT=11/7788/103]
Jan 1 03:00:55 unknown user.info kernel: vlan1: dev_set_promiscuity(master, 1)
Jan 1 03:00:55 unknown user.info kernel: device eth0 entered promiscuous mode
Jan 1 03:00:55 unknown user.info kernel: device vlan1 entered promiscuous mode
Jan 1 03:00:55 unknown user.info kernel: usb 1-1.7: new high speed USB device using ehci_hcd and address 5
Jan 1 03:00:55 unknown user.info kernel: usb 1-1.7: configuration #1 chosen from 1 choice
Jan 1 03:00:55 unknown user.info kernel: scsi1 : SCSI emulation for USB Mass Storage devices
Jan 1 03:00:55 unknown user.debug hotplug[552]: Attached USB device 1-1.7:1.0 [INTERFACE=8/6/80 PRODUCT=bc2/2312/219]
Jan 1 03:00:56 unknown user.warn kernel: COEX: downgraded chanspec 0x2e09 to 0x2b0b: channel 4 used by exiting BSSs
Jan 1 03:00:56 unknown user.warn kernel: COEX: downgraded chanspec 0x2d03 to 0x2b01: channel 4 used by exiting BSSs
Jan 1 03:00:56 unknown user.warn kernel: COEX: downgraded chanspec 0x2d06 to 0x2b04: channel 1 used by exiting BSSs
Jan 1 03:00:57 unknown user.notice kernel: scsi 0:0:0:0: Direct-Access Generic Flash Disk 8.00 PQ: 0 ANSI: 2
Jan 1 03:00:57 unknown user.notice kernel: sd 0:0:0:0: [sda] 3891200 512-byte hardware sectors (1992 MB)
Jan 1 03:00:57 unknown user.notice kernel: sd 0:0:0:0: [sda] Write Protect is off
Jan 1 03:00:57 unknown user.debug kernel: sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
Jan 1 03:00:57 unknown user.err kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Jan 1 03:00:57 unknown user.err kernel: sd 0:0:0:0: [sda] Assuming drive cache: write through
Jan 1 03:00:57 unknown user.info kernel: sda:<5>scsi 1:0:0:0: Direct-Access Seagate Expansion 0219 PQ: 0 ANSI: 6
Jan 1 03:00:57 unknown user.notice kernel: sd 1:0:0:0: [sdb] 1953525167 512-byte hardware sectors (1000205 MB)
Jan 1 03:00:57 unknown user.notice kernel: sd 1:0:0:0: [sdb] Write Protect is off
Jan 1 03:00:57 unknown user.debug kernel: sd 1:0:0:0: [sdb] Mode Sense: 2b 00 10 08
Jan 1 03:00:57 unknown user.err kernel: sd 1:0:0:0: [sdb] Assuming drive cache: write through
Jan 1 03:00:57 unknown user.err kernel: sd 1:0:0:0: [sdb] Assuming drive cache: write through
Jan 1 03:00:57 unknown user.info kernel: sdb: sda1 sda2
Jan 1 03:00:57 unknown user.notice kernel: sd 0:0:0:0: [sda] Attached SCSI removable disk
Jan 1 03:00:58 unknown user.warn kernel: sdb1
Jan 1 03:00:58 unknown user.notice kernel: sd 1:0:0:0: [sdb] Attached SCSI disk
Jan 1 03:00:58 unknown user.info kernel: device eth1 entered promiscuous mode
Jan 1 03:00:58 unknown user.info kernel: br0: port 2(eth1) entering forwarding state
Jan 1 03:00:58 unknown user.info kernel: br0: port 1(vlan1) entering forwarding state
Jan 1 03:00:58 unknown user.warn kernel: vlan2: Setting MAC address to 84 1b 5e 30 ff 8d.
Jan 1 03:00:58 unknown user.debug kernel: vlan2: add 33:33:00:00:00:01 mcast address to master interface
Jan 1 03:00:58 unknown user.debug kernel: vlan2: add 01:00:5e:00:00:01 mcast address to master interface
Jan 1 03:00:58 unknown user.info kernel: IMQ starting with 2 devices...
Jan 1 03:00:58 unknown user.info kernel: IMQ driver loaded successfully.
Jan 1 03:00:58 unknown user.info kernel: Hooking IMQ after NAT on PREROUTING.
Jan 1 03:00:58 unknown user.info kernel: Hooking IMQ before NAT on POSTROUTING.
Jan 1 03:01:01 unknown daemon.info pppd[643]: Plugin rp-pppoe.so loaded.
Jan 1 03:01:01 unknown daemon.info pppd[643]: RP-PPPoE plugin version 3.10 compiled against pppd 2.4.5
Jan 1 03:01:01 unknown user.info redial[645]: Started. Time: 10
Jan 1 03:01:01 unknown daemon.notice pppd[644]: pppd 2.4.5 started by root, uid 0
Jan 1 03:01:02 unknown authpriv.info dropbear[652]: Running in background
Jan 1 03:01:02 unknown daemon.info pppd[644]: PPP session is 50277 (0xc465)
Jan 1 03:01:02 unknown daemon.warn pppd[644]: Connected to e8:04:62:27:80:10 via interface vlan2
Jan 1 03:01:02 unknown daemon.info pppd[644]: Using interface ppp0
Jan 1 03:01:02 unknown daemon.notice pppd[644]: Connect: ppp0 <--> vlan2
Jan 1 03:01:02 unknown daemon.notice pppd[644]: CHAP authentication succeeded
Jan 1 03:01:02 unknown daemon.notice pppd[644]: peer from calling number E8:04:62:27:80:10 authorized
Jan 1 03:01:02 unknown daemon.notice pppd[644]: local IP address 95.221.168.34
Jan 1 03:01:02 unknown daemon.notice pppd[644]: remote IP address 212.1.254.127
Jan 1 03:01:02 unknown daemon.notice pppd[644]: primary DNS address 212.1.224.6
Jan 1 03:01:02 unknown daemon.notice pppd[644]: secondary DNS address 212.1.244.6
Jan 1 03:01:02 unknown user.debug ip-up[664]: 182: pptp peerdns disabled
Jan 1 03:01:03 unknown daemon.info dnsmasq[666]: started, version UNKNOWN cachesize 1500
Jan 1 03:01:03 unknown daemon.info dnsmasq[666]: compile time options: IPv6 GNU-getopt no-RTC no-DBus no-i18n no-IDN DHCP DHCPv6 no-Lua TFTP no-conntrack Tomato-helper auth
Jan 1 03:01:03 unknown daemon.info dnsmasq[666]: asynchronous logging enabled, queue limit is 5 messages
Jan 1 03:01:03 unknown daemon.info dnsmasq-dhcp[666]: DHCP, IP range 10.137.12.2 -- 10.137.12.254, lease time 1d
Jan 1 03:01:03 unknown daemon.info dnsmasq[666]: reading /etc/resolv.dnsmasq
Jan 1 03:01:03 unknown daemon.info dnsmasq[666]: using nameserver 212.1.244.6#53
Jan 1 03:01:03 unknown daemon.info dnsmasq[666]: using nameserver 212.1.224.6#53
Jan 1 03:01:03 unknown daemon.info dnsmasq[666]: read /etc/hosts - 2 addresses
Jan 1 03:01:03 unknown daemon.info dnsmasq[666]: read /etc/dnsmasq/hosts/hosts - 8 addresses
Jan 1 03:01:03 unknown daemon.info dnsmasq-dhcp[666]: read /etc/dnsmasq/dhcp/dhcp-hosts
Jan 1 03:01:05 unknown user.debug init[1]: starting rstats.
Jan 1 03:01:05 unknown user.debug init[1]: starting cstats.
Jan 1 03:01:05 unknown daemon.err apcupsd[499]: apcupsd FATAL ERROR in linux-usb.c at line 609 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see <http://www.apcupsd.com/support.html>.
Jan 1 03:01:05 unknown daemon.err apcupsd[499]: apcupsd error shutdown completed
Jan 1 03:01:06 unknown daemon.info dnsmasq-dhcp[666]: DHCPREQUEST(br0) 10.137.12.2 90:2b:34:9d:76:c8
Jan 1 03:01:06 unknown daemon.info dnsmasq-dhcp[666]: DHCPACK(br0) 10.137.12.2 90:2b:34:9d:76:c8 PC-MATRIX
Jan 1 03:01:28 unknown user.info kernel: usb 1-1.6: reset high speed USB device using ehci_hcd and address 4
Jan 1 03:01:29 unknown user.info hotplug[564]: USB ext2 fs at /dev/sda1 mounted on /tmp/mnt/sda1
Jan 1 03:01:29 unknown auth.info login[802]: root login on 'pts/0'
Jan 1 03:01:34 unknown user.info kernel: Adding 511992k swap on /dev/sda2. Priority:-1 extents:1 across:511992k
Jan 1 03:02:06 unknown user.warn kernel: fuse init (API version 7.8), DCACHE_BUG enabled
Jan 1 03:02:08 unknown daemon.notice ntfs-3g[840]: Version 2013.1.13 integrated FUSE 27
Jan 1 03:02:08 unknown daemon.notice ntfs-3g[840]: Mounted /dev/sdb1 (Read-Write, label "", NTFS 3.1)
Jan 1 03:02:08 unknown daemon.notice ntfs-3g[840]: Cmdline options: iocharset=utf8,noatime,nodev
Jan 1 03:02:08 unknown daemon.notice ntfs-3g[840]: Mount options: iocharset=utf8,nodev,allow_other,nonempty,noatime,fsname=/dev/sdb1,blkdev,blksize=4096
Jan 1 03:02:08 unknown daemon.notice ntfs-3g[840]: Ownership and permissions disabled, configuration type 1
Jan 1 03:02:08 unknown user.info hotplug[572]: USB ntfs fs at /dev/sdb1 mounted on /tmp/mnt/sdb1
Apr 4 11:24:14 unknown daemon.info pppd[644]: System time change detected.
Apr 4 11:24:33 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 11:24:33 unknown user.notice root: Stoping NFS Server ...
Apr 4 11:24:33 unknown user.info init[1]: Netgear WNR3500L v2: Tomato 1.28.0000 MIPSR2-108 K26 USB AIO
Apr 4 11:24:33 unknown user.notice root: NFS Server stoped ...
Apr 4 11:24:45 unknown user.err syslog: transmission-daemon Error loading config file -- exiting. (daemon.c:491)
Apr 4 11:24:45 unknown user.notice root: Transmission daemon successfully started
Apr 4 11:24:54 unknown cron.err crond[672]: time disparity of 22751002 minutes detected
Apr 4 11:24:55 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 11:24:56 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 11:25:06 unknown user.err syslog: transmission-daemon Error loading config file -- exiting. (daemon.c:491)
Apr 4 11:25:06 unknown user.notice root: Transmission daemon successfully started
Apr 4 11:25:26 unknown daemon.info dnsmasq-dhcp[666]: DHCPREQUEST(br0) 10.137.12.3 48:5d:60:ad:58:4b
Apr 4 11:25:26 unknown daemon.info dnsmasq-dhcp[666]: DHCPACK(br0) 10.137.12.3 48:5d:60:ad:58:4b PLANSHET-MATRIX
Apr 4 11:30:01 unknown user.notice root: Transmission stopped? Starting...
Apr 4 11:30:01 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 11:30:02 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 11:30:12 unknown user.err syslog: transmission-daemon Error loading config file -- exiting. (daemon.c:491)
Apr 4 11:30:12 unknown user.notice root: Transmission daemon successfully started

Свернуть

Как видно из лога есть ошибка transmission-daemon Error loading config file -- exiting. (daemon.c:491) и нкак не поправить. Настройки Transmission хранятся на флешке ext2. В настройках фаервола:
iptables -I INPUT -p tcp --dport 65534 -j ACCEPT
iptables -I INPUT -p udp --dport 65534 -j ACCEPT
iptables -I INPUT -p tcp --dport 51413 -j ACCEPT
iptables -I INPUT -p tcp --dport 9091 -j ACCEPT
также прописал в конфиг
"peer-port" : 51413,
"rpc-enabled": true,
"rpc-whitelist-enabled": true,
"rpc-whitelist": "127.0.0.1,10.137.12.*",
"rpc-url": "/transmission/"
Утройства USB
Generic Flash Disk
Partition 'sda1' ext2 (1,377.00 MB / 1,374.90 MB free) is mounted on /tmp/mnt/sda1
Partition 'sda2' swap (499.99 MB) is active
Seagate Expansion
Partition 'sdb1' fuseblk (931.51 GB / 903.94 GB free) is mounted on /tmp/mnt/sdb1
Printer lp0 Samsung ML-1640 Series
А еще ошибка:
Jan 1 03:01:05 unknown daemon.err apcupsd[499]: apcupsd FATAL ERROR in linux-usb.c at line 609 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see <http://www.apcupsd.com/support.html>.
Jan 1 03:01:05 unknown daemon.err apcupsd[499]: apcupsd error shutdown completed
Помогите плз в поисках уже роутер убил, пришлость через шнурок вытаскивать

[Radjah]

На странце настройки качалки полностью очисти поле дополнительных опций.
По теме ошибки UPS читай самый верх этой страницы.

[MatrixNet]

Можно подробнее как настроить качалку.

 

Apr 4 12:52:09 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:52:10 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:52:20 unknown user.err syslog: transmission-daemon Error loading config file -- exiting. (daemon.c:491)
Apr 4 12:52:20 unknown user.notice root: Transmission daemon successfully started
Apr 4 12:52:23 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:52:24 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:52:34 unknown user.err syslog: transmission-daemon Error loading config file -- exiting. (daemon.c:491)
Apr 4 12:52:34 unknown user.notice root: Transmission daemon successfully started
Apr 4 12:52:54 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:52:55 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:53:05 unknown user.err syslog: transmission-daemon Error loading config file -- exiting. (daemon.c:491)
Apr 4 12:53:05 unknown user.notice root: Transmission daemon successfully started
Apr 4 12:53:17 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:53:18 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:53:28 unknown user.err syslog: transmission-daemon Error loading config file -- exiting. (daemon.c:491)
Apr 4 12:53:28 unknown user.notice root: Transmission daemon successfully started
Apr 4 12:53:30 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:53:31 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:53:41 unknown user.err syslog: transmission-daemon Error loading config file -- exiting. (daemon.c:491)
Apr 4 12:53:41 unknown user.notice root: Transmission daemon successfully started
Apr 4 12:56:56 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:56:56 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:57:06 unknown user.err syslog: transmission-daemon Error loading config file -- exiting. (daemon.c:491)
Apr 4 12:57:06 unknown user.notice root: Transmission daemon successfully started
Apr 4 12:57:35 unknown user.notice root: Transmission daemon successfully stoped
Apr 4 12:57:36 unknown user.notice root: Transmission daemon successfully stoped

Свернуть

А если запускается после ребута то не врубается GUI:

 

Apr 4 12:47:42 unknown daemon.info transmission-daemon[1087]: Transmission 2.77 (14031) started (session.c:722)
Apr 4 12:47:42 unknown daemon.info transmission-daemon[1087]: RPC Server Adding address to whitelist: 127.0.0.1 (rpc-server.c:803)
Apr 4 12:47:42 unknown daemon.info transmission-daemon[1087]: RPC Server Serving RPC and Web requests on port 127.0.0.1:9091/transmission/ (rpc-server.c:997)
Apr 4 12:47:42 unknown daemon.info transmission-daemon[1087]: RPC Server Whitelist enabled (rpc-server.c:1001)
Apr 4 12:47:42 unknown daemon.info transmission-daemon[1087]: DHT Generating new id (tr-dht.c:309)
Apr 4 12:47:42 unknown daemon.info transmission-daemon[1087]: Port Forwarding (NAT-PMP) initnatpmp succeeded (0) (natpmp.c:72)
Apr 4 12:47:42 unknown daemon.info transmission-daemon[1087]: Port Forwarding (NAT-PMP) sendpublicaddressrequest succeeded (2) (natpmp.c:72)
Apr 4 12:47:42 unknown daemon.info transmission-daemon[1087]: Using settings from "/tmp/mnt/Torrent/.settings" (daemon.c:517)
Apr 4 12:47:42 unknown daemon.info transmission-daemon[1087]: Saved "/tmp/mnt/Torrent/.settings/settings.json" (bencode.c:1738)
Apr 4 12:47:42 unknown daemon.info transmission-daemon[1087]: Port Forwarding Starting (port-forwarding.c:93)
Apr 4 12:48:01 unknown daemon.info transmission-daemon[1087]: DHT Attempting bootstrap from dht.transmissionbt.com (tr-dht.c:247)
Apr 4 12:49:41 unknown daemon.info transmission-daemon[1087]: Port Forwarding Starting (port-forwarding.c:93)

Свернуть

 

403: Forbidden
Unauthorized IP Address.
Either disable the IP address whitelist or add your address to it.
If you're editing settings.json, see the 'rpc-whitelist' and 'rpc-whitelist-enabled' entries.
If you're still using ACLs, use a whitelist instead. See the transmission-daemon manpage for details.

Свернуть

Не смотря на то, что в настройках есть:

 

"rpc-url": "/transmission/",
"rpc-whitelist": "127.0.0.*,10.137.12.*",

Свернуть

[Nite2]

MatrixNet, с какого адреса вы подсоединяетесь GUI к transmission? Я правильно понимаю, что вы пытаетесь включить rpc-whitelist, но при этом, если задаете дополнительные адреса, кроме 127.0.0.1, типа 10.137.12.*, то при старте демона вылетает ошибка загрузки конфигурационного файла?
С отключенным rpc-whitelist демон запускается? Зайти через GUI можете?

[MatrixNet]

Не совсем, запуск редкий сразу после старта роутера, если же при сохранении настроек идет перезапуск Transmission, то ошибка конфига.
Несмотря на то, что он при старте роутера запускается, в Web Gui или Gui от Google, он выдает 403 ошибку.
вот конфиг в итоге:

 

{
"alt-speed-down": 50,
"alt-speed-enabled": false,
"alt-speed-time-begin": 540,
"alt-speed-time-day": 127,
"alt-speed-time-enabled": false,
"alt-speed-time-end": 1020,
"alt-speed-up": 50,
"bind-address-ipv4": "0.0.0.0",
"bind-address-ipv6": "::",
"blocklist-enabled": false,
"blocklist-url": "http://www.example.com/blocklist",
"cache-size-mb": 2,
"dht-enabled": true,
"download-dir": "//Downloads",
"download-queue-enabled": true,
"download-queue-size": 5,
"encryption": 0,
"idle-seeding-limit": 30,
"idle-seeding-limit-enabled": false,
"incomplete-dir": "//Downloads",
"incomplete-dir-enabled": false,
"lpd-enabled": false,
"message-level": 2,
"peer-congestion-algorithm": "",
"peer-limit-global": 240,
"peer-limit-per-torrent": 60,
"peer-port": 51413,
"peer-port-random-high": 65535,
"peer-port-random-low": 49152,
"peer-port-random-on-start": false,
"peer-socket-tos": "default",
"pex-enabled": true,
"port-forwarding-enabled": true,
"preallocation": 1,
"prefetch-enabled": 0,
"queue-stalled-enabled": true,
"queue-stalled-minutes": 30,
"ratio-limit": 2,
"ratio-limit-enabled": false,
"rename-partial-files": true,
"rpc-authentication-required": True,
"rpc-bind-address": "0.0.0.0",
"rpc-enabled": true,
"rpc-password": "",
"rpc-port": 9091,
"rpc-url": "/transmission/",
"rpc-username": "Matrix",
"rpc-whitelist": "127.0.0.1,10.137.12.*",
"rpc-whitelist-enabled": true,
"scrape-paused-torrents-enabled": true,
"script-torrent-done-enabled": false,
"script-torrent-done-filename": "",
"seed-queue-enabled": false,
"seed-queue-size": 10,
"speed-limit-down": 100,
"speed-limit-down-enabled": false,
"speed-limit-up": 100,
"speed-limit-up-enabled": false,
"start-added-torrents": true,
"trash-original-torrent-files": false,
"umask": 18,
"upload-slots-per-torrent": 14,
"utp-enabled": true
}

Свернуть

Спасибо за попытку помоч, уже вроде разобрался

Встал новый вопрос при старте роутера Transmission сам стартует, а где можно строку запуска стереть или поправить ? т.к. transmission-daemon -g /tmp/mnt/sda1/Torrent/.settings я запускаю то стандартная настройка мне не подходит.
Зарание спс